Automotive Service III (2016): Grades 9, 10, 11, 12

Understand Engine Service

Understand Automatic Transmission/Transaxle Service

Understand Manual Drive Train & Axle Service

Understand Suspension & Steering Service

Understand Brake Service

Understand Electrical/Electronic System Service

Understand Heating & Air Conditioning Service

Understand Engine Performance Service

Preparing Vehicle For Customer

Personal Standards

Work Habits/Ethic

Remove and replace timing belt; verify correct camshaft timing.

Adjust valves (mechanical or hydraulic lifters).

Inspect for leakage at external seals, gaskets, and bushings.

Inspect replace and align power train mounts.

Describe the operational characteristics of a continuously variable transmission (CVT).

Describe the operational characteristics of a hybrid vehicle drive train.

Describe the operational characteristics of an electronically-controlled manual transmission/transaxle.

Inspect, remove, and replace front wheel drive (FWD) bearings, hubs, and seals.

Inspect, service, and replace shafts, yokes, boots, and universal/CV joints.(Phasing)

Inspect and replace drive axle wheel studs.

Inspect front-wheel bearings and locking hubs.

Check for leaks at drive assembly seals; check vents; check lube level.

Road test the vehicle to verify drive train noises and vibration.

Disable and enable supplemental restraint system (SRS).

Inspect electric power-assisted steering.

Perform prealignment inspection and measure vehicle ride height; determine necessary action.

Inspect and replace steering linkage damper(s).

Identify alignment-related symptoms such as vehicle wander, drift, and pull.

Measure front and rear wheel camber; adjust as needed.

Measure caster; adjust as needed.

Measure front wheel toe; adjust as needed.

Center the steering wheel using mechanical methods.

Measure rear wheel toe; adjust as needed.

Measure thrust angle.

Calibrate steering angle sensor

Inspect non-independent front axle assembly for damage and misalignment.

Inspect non-independent rear axle assembly for damage and misalignment.

Measure brake pedal height, travel, and free play (as applicable); determine necessary action.

Check brake pedal travel with, and without, engine running to verify proper power booster operation.

Check vacuum supply (manifold or auxiliary pump) to vacuum-type power booster.

Check parking brake cables and components for wear, binding, and corrosion; clean, lubricate, adjust or replace as needed.

Replace wheel bearing and race.

Inspect and replace wheel studs.

Identify traction control/vehicle stability control system components.

Describe the operation of a regenerative braking system.

Demonstrate proper use of a digital multimeter (DMM) when measuring source voltage, voltage drop (including grounds), current flow, and resistance.

Demonstrate knowledge of the causes and effects from shorts, grounds, opens, and resistance problems in electrical/electronic circuits.

Check operation of electrical circuits with a test light.

Check operation of electrical circuits with fused jumper wires.

Measure key-off battery drain (parasitic draw).

Identify electronic modules, security systems, radios, and other accessories that require reinitialization or code entry after reconnecting vehicle battery.

Perform starter circuit voltage drop tests; determine necessary action.

Perform charging circuit voltage drop tests; determine necessary action.

Disable and enable airbag system for vehicle service; verify indicator lamp operation.

Describe the operation of keyless entry/remote-start systems.

Identify the source of A/C system odors.

Perform engine absolute (vacuum/boost) manifold pressure tests; determine necessary action

Perform cylinder power balance test; determine necessary action.

Perform cylinder cranking and running compression tests; determine necessary action.

Perform cylinder leakage test; determine necessary action.

Retrieve and record diagnostic trouble codes, OBD monitor status, and freeze frame data; clear codes when applicable.

Describe the importance of operating all OBDII monitors for repair verification.

Ensure vehicle is prepared to return to customer per school/company policy. (floor mats, steering wheel cover, etc.)

Reports to work daily on time; able to take directions and motivated to accomplish the task at hand.

Dresses appropriately and uses language and manners suitable for the workplace.

Maintains appropriate personal hygiene.

Meets and maintains employment eligibility criteria, such as drug/alcohol-free status, clean driving record, etc.

Demonstrates honesty, integrity, and reliability.

Complies with workplace policies/laws.

Contributes to the success of the team, assists others and requests help when needed.

Works well with all customers and coworkers.

Negotiates solutions to interpersonal and workplace conflicts.

Contributes ideas and initiative.

Follows directions.

Communicates (written and verbal) effectively with customers and coworkers.

Reads and interprets workplace documents; writes clearly and concisely.

Analyzes and resolves problems that arise in completing assigned tasks.

Organizes and implements a productive plan of work.

Uses scientific, technical, engineering and mathematics principles and reasoning to accomplish assigned tasks.

Identifies and address the needs of all customers, providing helpful, courteous and knowledgeable service and advice as needed.